QQ客服 官方微博 反馈留言

浏览/检索结果: 共6条，第1-6条 帮助 已选(0)清除 条数/页：5101520253035404550556065707580859095100   排序方式：请选择作者升序作者降序题名升序题名降序发表日期升序发表日期降序提交时间升序提交时间降序 Highly anisotropic functional conductors fabricated by multi-melt multi-injection molding : A synergetic role of multiple melt flows and confined interface 期刊论文 Composites Science and Technology, 2019, 卷号: Vol.171, 页码: 127-134 作者:  Yanhao Huang;  Zhengying Liu;  Rui Chen;  Shaodi Zheng;  Changping Feng 收藏  |  浏览/下载：4/0  |  提交时间：2019/02/25 Multi-melt  multi-injection  molding  (M3IM)  Plan-orientation  Anisotropic  property  Electric  conductivity  Thermal  conductivity  Second  shear  flow  and  confined  interface   Diverse interfacial crystalline morphologies induced by poly (d-lactide) (PDLA) melt penetration process in multi-melt multi-injection molding ((MIM)-I-3) system 期刊论文 COMPOSITES PART B-ENGINEERING, 2018, 卷号: Vol.153, 页码: 429-436 作者:  Chen, Rui;  Huang, Yan-Hao;  Liu, Lei;  Chen, Li-Bo;  Liu, Zheng-Ying 收藏  |  浏览/下载：4/0  |  提交时间：2019/02/25 Multi-melt multi-injection molding  Stereocomplex crystal   The formation of interfacial morphologies of iPP derived from transverse flow during multi-penetration in secondary melt flow 期刊论文 Materials Today Communications, 2017, 卷号: Vol.12, 页码: 43-54 作者:  Yanhao Huang;  Xiaochao Xia;  Zhengying Liu;  Wei Yang;  Chunxia Zhu 收藏  |  浏览/下载：13/0  |  提交时间：2019/03/26 Multi-melt  multi-injection  molding  (M3IM)  Transverse  flow  (TF)  β-Cylindrites  Shish-kebab  Relaxation   Hierarchical Crystalline Structures Induced by Temperature Profile in HDPE Bars during Melt Penetration Process 期刊论文 高分子科学（英文版）, 2017, 卷号: No.1 - 收藏  |  浏览/下载：3/0  |  提交时间：2019/03/26 Hierarchical  structures  Orientation  Multi-melt  multi-injection  molding  Mold  temperature   Effect of Viscosity Ratio on the Crystalline Morphologies and Mechanical Property of Multi-Melt Multi-Injection Molded Parts 期刊论文 Polymer-Plastics Technology and Engineering, 2014, 卷号: Vol.53 No.12, 页码: 1272-1282 作者:  Feng, Jian;  Yang, Wei;  Zhang, Rui-yan;  Wu, Jing-jing;  Wang, Long 收藏  |  浏览/下载：1/0  |  提交时间：2019/03/26 Crystalline  morphology  Mechanical  properties  Multi-melt  multi-injection  molding  Orientation  Viscosity  ratio   Determination of optimum process parameters in gas-assisted injection molding (EI CONFERENCE) 会议论文 2011 International Conference on Electrical Information and Mechatronics, ICEIM2011, December 23, 2011 - December 25, 2011, Jiaozuo, China Zi K.; Chen L. 收藏  |  浏览/下载：13/0  |  提交时间：2013/03/25 With finite element analysis software Moldflow  numerical simulation and studies about FM truck roof handle were conducted on gas-assisted injection molding process. The influences of melt pre-injection shot  gas pressure  delay time and melt temperature were observed by using multi-factor orthogonal experimental method. According to the analysis of the factors' impact on evaluation index  the optimized parameter combination is obtained. Therefore the optimization design of technological parameters is done. The results show that during the gas-assisted injection molding  optimum pre-injection shot is 94%  gas pressure is 15MPa  delay time is 0.5s  melt temperature is 240 C. This study provided a more practical approach for the gas-assisted injection molding process optimization.