QQ客服 官方微博 反馈留言

浏览/检索结果: 共5条，第1-5条 帮助 限定条件 发表日期：2020    专题：兰州理工大学    第一署名单位    第一作者单位    通讯作者单位     已选(0)清除 条数/页：5101520253035404550556065707580859095100   排序方式：请选择作者升序作者降序题名升序题名降序发表日期升序发表日期降序提交时间升序提交时间降序 A 3D dynamic analysis of different depositing processes used in wire arc additive manufacturing 期刊论文 Materials Today Communications, 2020, 卷号: 24 作者:  Huang, Jiankang;  Guan, Zhichen;  Yu, Shurong;  Yu, Xiaoquan;  Yuan, Wen 收藏  |  浏览/下载：3/0  |  提交时间：2020/11/14 3D printers  Additives  Residual stresses  Temperature  3-D dynamic analysis  Depositing process  Experimental and numerical analysis  Heat conditions  Plastic distortions  Wire arc   Influence of Co content on the microstructures and mechanical properties of a Ni–Co base superalloy made by specific additive manufacturing process 期刊论文 Materials Science and Engineering A, 2020, 卷号: 786 作者:  Tang, Ling;  Liang, Jingjing;  Cui, Chuanyong;  Li, Jinguo;  Zhou, Yizhou 收藏  |  浏览/下载：3/0  |  提交时间：2022/02/17 3D printers  Additives  Deformation  Heat treatment  High resolution transmission electron microscopy  Mechanical properties  Metal testing  Microstructure  Scanning electron microscopy  Stacking faults  Superalloys  Tensile testing  Twinning  Additive manufacturing process  Columnar microstructures  Deformation mechanism  Interdendritic regions  Microstructure observation  Microstructures and mechanical properties  Stacking fault energies  Standard heat treatments   Influence of Co content on the microstructures and mechanical properties of a Ni–Co base superalloy made by specific additive manufacturing process 期刊论文 Materials Science and Engineering A, 2020, 卷号: 786 作者:  Tang, Ling;  Liang, Jingjing;  Cui, Chuanyong;  Li, Jinguo;  Zhou, Yizhou 收藏  |  浏览/下载：3/0  |  提交时间：2020/11/14 3D printers  Additives  Deformation  Heat treatment  High resolution transmission electron microscopy  Mechanical properties  Metal testing  Microstructure  Scanning electron microscopy  Stacking faults  Superalloys  Tensile testing  Twinning  Additive manufacturing process  Columnar microstructures  Deformation mechanism  Interdendritic regions  Microstructure observation  Microstructures and mechanical properties  Stacking fault energies  Standard heat treatments   Properties of Copper-Based Bulks Materials Produced by Low Pressure Cold Spray Additives 期刊论文 Xiyou Jinshu Cailiao Yu Gongcheng/Rare Metal Materials and Engineering, 2020, 卷号: 49, 期号: 5, 页码: 1729-1735 作者:  Feng, Li;  Li, Dongting;  Chang, Jirong;  An, Guosheng;  Li, Wensheng 收藏  |  浏览/下载：2/0  |  提交时间：2020/11/14 Additives  Alumina  Aluminum oxide  Annealing  Copper  Manufacture  Materials handling equipment  Tensile strength  Additive manufacturing technology  Al2O3 contents  Annealing temperatures  Bulk materials  Cold-sprayed  Copper-based  Low pressures  Volume ratio   Droplet transfer behavior in bypass-coupled wire arc additive manufacturing 期刊论文 JOURNAL OF MANUFACTURING PROCESSES, 2020, 卷号: 49, 页码: 397-412 作者:  Huang, Jiankang;  Yuan, Wen;  Yu, Shurong;  Zhang, Linbo;  Yu, Xiaoquan 收藏  |  浏览/下载：12/0  |  提交时间：2020/06/02 Wire arc  Additive manufacturing  Droplet transfer  Bypass coupled arc